Software getest en ziet er beter uit als 6.4.2.

KNOWN ISSUE: Named clients can cause malformed JSON, resulting in striped pattern on the outage graph due to check-in failure.

KNOWN ISSUE: Layer 7 traffic for wired clients not reported.

KNOWN ISSUE: Disabled LEDs could turn themselves back on after upgrade.

FIX: Channel scan could send incorrect channel values causing Auto channel mode to fail.

FIX: LED may get stuck showing white color.

FIX: When Status LEDs were turned off, the LEDs would remain off even during reconfiguration or an error events.

FIX: Mesh interface could get set to managed mode, leaving repeaters orphaned.

FIX: Upload/Download usage reporting could get reversed.

FIX: Bandwidth throttling was not always being applied to some clients, when the SSID was bridged to a VLAN or afterВ a WiFi Scheduling event.

NEW: BATMAN Mesh Protocol reverted to BATMAN IV, to restore repeater mesh compatibility with 6.3.x firmware.

#FIX CVE 2017 14491 FOR MAC UPGRADE#

NEW: Firmware upgrade delay reduced and firmware can upgrade when in orphan mode, allowing for faster firmware updates.

NEW: Prefer 5Ghz 802.11ac meshing, if available.

NEW: Client IP addresses reported to CloudTrax.

#FIX CVE 2017 14491 FOR MAC MAC#

This results in a different MAC address being used for DHCP requests compared to 6.4.2/ 6.4.1.

KNOWN ISSUE: The A42 802.3af port now uses the MAC address shown on the underside sticker, instead of the sticker MAC address +1.

KNOWN ISSUE: AP may report N/A N/A for channels, despite broadcasting correctly.

KNOWN ISSUE: Using the SSID Band setting вЂњBoth вЂ“ Unique SSIDsвЂќ, results in the first character of each SSID name being truncated.

The AP may continue to broadcast both bands.

KNOWN ISSUE: вЂњ2.4Ghz onlyвЂќ and вЂњ5Ghz onlyвЂќ band setting may not be honored if another SSID is set to use вЂњBoth вЂ“ Combined SSIDвЂќ.

FIXED: Disabled LED lights may turn back on after firmware upgrade.

FIXED: SSIDs may fail to broadcast with WiFi Scheduling enabled.

FIXED: External splash pages that worked in 6.3 firmware fail to work on 6.4 firmware due to internal CONN_ERR.

FIXED: Clients w/ hostnames may cause malformed JSON, resulting in striped pattern on the outage graph due to check-in failure.

FIXED: Facebook WiFi would not pop-up automatically or would be displayed incorrectly on iOS and macOS devices.

New: If AP Mesh is disabled, access point will reconfigure channel changes immediately.

NEW: Bridge Loop Avoidance is now more aggressiveВ to avoid looping scenarios on complex networks.

NEW: Unused splash page images are now deleted automatically from the access point when SSID settings are saved.

Only 802.11s is supported, so 6.4.5+ firmware will no longer mesh with APs running 6.3 firmware.

This results in a different MAC address being used for DHCP requests compared to 6.4.2/6.4.1.

KNOWN ISSUE: IP address for wired clients not reported.

KNOWN ISSUE: Traffic for wired clients not reported when Application Reporting is turned off.

KNOWN ISSUE: вЂњ2.4Ghz onlyвЂќ and вЂњ5Ghz onlyвЂќ band setting may not be honored if another SSID is set to use the вЂњBoth вЂ“ Combined SSIDвЂќ.

KNOWN ISSUE: Disabling Application Reporting breaks throttling on non-bridged SSIDs.

KNOWN ISSUE: Some clients may report being connected to the wrong band(e.g.

FIXED: AP may report N/A N/A for channels, despite broadcasting correctly.

FIXED: Using the SSID Band setting вЂњBoth вЂ“ Unique SSIDsвЂќ, results in the first character of each SSID name being truncated.

6.4.5 (23-02-18) is de vervangende versie voor 6.3.16 Open-Mesh gaat niet verder met 6.3 en maken van 6.4.5 een вЂњstable releaseвЂќ